Type EWD-H-XP2 Elevator Load Weighing Device

INTRODTION MANUAL

● This system is applicable to all elevators with movable car platform in need of overload signals. This device is of extremely high performance-price ratio. This appliance is to overcome the inherent disadvantage of the mechanical overload switch and to replace it.

• Main characters:

• 1.Working in a contactless and inductive way. No mechanical movement itself. Being directly installed in the original place of overload switch. No necessity of changing the mechanism of elevator car.
• 2.Adopting strong inductive magnet, improving the anti-interference of the system to the utmost.
• 3.The electrical property is in compliance with the standard of the International Electro-technical Commission (IEC).
• 4.Rated relay dynamic open, overload relay -dynamic close and output-break are easy for customers to use.
• 5.More accurately positioning, small overall size, easy installation and adjustment, simple structure and low price.

• ⒈	Application Range	Applicable to all elevators with movable car platform in need of overload signal with a inspection clearance of 8～15㎜.
  2	Sensitivity	Overload turning point≤Rated load adjusting point±0.05㎜ Rated load→overload retention gap≈0.50mm
  3	System Error	≤1.5% (5～40℃)
  4	Output Mode	1 pair of relay dynamic CLOSE or dynamic OPEN contacts respectively with the capacity of DC/AC 48V/500mA.
  5	Operation Ambient Temperature	-25～55℃
  6	Power Supply	AC/DC 24V(±10%)/15mA. The operating current of the whole machine≤100 mA.
  7	Install Position	Movable elevator car platform
  8	Overall Size	Column of Φ24×83 mm

• Working Principle:

This system weighs the elevator car load based on the principle of the elastic deformation of movable elevator car platform caused by loading with the HALL sensor measuring the change of displacement, fulfilling the aim of load weighing.

Adjustment

• 1.Please refer to the above figure to install this device with the connecting support (made by the customer himself) closing the middle part of the car platform as near as possible.
• 2.Let the magnet adhesive on the car platform with the marking-face right facing the induction point of the device.

• 3.Install and adjust this device so that the magnet on the car platform aiming at the center point of its upper face. Meanwhile, assure the end face of this device in parallel with that of the magnet.
• 4.When elevator is of rated load, adjust this device up and down to make the indicator just turn green, red one turn down , at this time, fasten this device and the adjustment is finished.
• 5.At the time of overload, indicator of this device keeps green and red on.

• The principle of system wiring:

Do use the Dyn. Open or Dyn. Close at the same time with full load

or overload when system wiring, avoiding cross using.

Attention : Output wire of this device must not be connected with external power supply to avoid everlasting damage.

• Others:

Accessory: Inductive magnet [20×20×3mm3] 1 piece Fastening Nut Φ4X20 : 2 sets

If there is any abnormality during adjustment or operation, contact our company directly.

• Attention:

1. The inductive magnet is specially made of rare earth magnet with strong magnetism for this product. Take special care in the course of installation. Don’t let it close to the high temperature above 100℃ to avoid demagnetization and our company will not be responsible for the personal hurt and equipment damage arising from this.

2. It is suitable for massive purchase.

XI'AN Excellent Electromechanical Co. Ltd

XI'AN EXCELLENT ELECTROMECHANICAL CO.,LTD was established in 2006, gathering the selling , research and development into one group, and specialized in popularization and using of elevator load weighing devices, relays, and vibration dampers, which necessarily provide the safe protection for the elevator and heavy mechanical machine. However, we also run elevator, elevator accessories, mechanical and electrical equipments as well as its fittings, such as elevator five-party talkback system, CEDE . door lock…

2014 Gangzhou WEE EXPO:

2016 May 10-13, Shanghai WEE EXPO:

How to make the order?

How to ship out?

By international express（DHL,TNT,EMS,UPS,FEDEX）, by sea, by air

How to payment for us?

How to contact with us?